HVAC Replacement Sales: From the Home Visit to a Good, Better, Best Proposal
Comfort questions first, then the load calculation and the duct check, then three options built from what the homeowner told you. The checklist they bring.

A homeowner who calls about a dead furnace or a struggling air conditioner is not shopping for a brand. They want the house comfortable again, they want to know the price is fair, and they want to trust the person standing in their utility room. The replacement visit that wins is the one that measures before it recommends.
The short version: run the visit in this order. Ask comfort questions, measure the home for a load calculation, check the ducts, then build three options from what the homeowner told you. Answer the questions on the federal bid checklist before they ask, and hand the crew a file they do not have to rebuild.
This guide covers the sales visit. Sizing, refrigerant work, permits and code belong to your licensed technicians and your local building department.
Before the visit
From the booking or the first call, find out:
- what is wrong: no heat, no cooling, uneven rooms, noise or rising bills,
- the age of the current system, if they know it,
- the fuel: gas, electric, oil or propane,
- who decides, and whether they can both be there, and
- anything already quoted by someone else.
The online booking guide shows how to collect this without a long form.
The comfort questions
Start in the living room, not the utility room. Ask, and write their words down:
- Which rooms are too hot or too cold, and when?
- Is there a room you avoid in summer or winter?
- Any dust, humidity or allergy problems?
- Is the system noisy? Where do you hear it?
- How long do you plan to stay in this home?
- Has anything changed since the old system went in: new windows, insulation, an addition, a finished basement?
- What did you like and dislike about the old system?
- How do you use the thermostat today?
These answers decide what goes in each option later. "The upstairs bedroom is always hot" is the reason zoning or duct work shows up in the proposal.
Measure before you recommend
Do not size the new system from the old one's label or a rule of thumb. The old system may have been the wrong size, and the house may have changed.
The ENERGY STAR bid comparison checklist tells homeowners that the contractor should calculate the home's heating and cooling loads using the ACCA Manual J method or an equivalent. Measure the rooms, the windows and the insulation, and run the calculation.
Then check the ducts. The same checklist asks whether the contractor will check existing ductwork and duct insulation for damage, and test the largest system the existing ducts can handle. Take photos of what you find: crushed runs, disconnected joints, missing insulation. Those photos explain your duct line items better than any sentence.
Note the rest for the technician: the electrical panel, the gas line and venting, the condensate drain, the equipment location and access.
Answer the checklist before they ask
That same ENERGY STAR checklist is built for homeowners comparing bids. It asks each contractor whether they will:
- measure the home and size the system with Manual J,
- install a properly matched indoor coil and outdoor unit, with the certificate that documents the match,
- check and repair the ducts, seal duct seams before insulating, and test for leaks,
- install new refrigerant lines rather than reuse the old ones,
- set up the thermostat and consider zoning,
- show the homeowner how to replace the filter,
- confirm refrigerant levels and airflow, and
- leave the manuals and the paperwork: the load calculation, the matching certificate and test results.
Turn your answers into a one page "what we do on every install" sheet, and hand it over at the visit. A homeowner holding three bids will notice which contractor answered the checklist without being asked.
Build three options from what they told you
Every option must fix the problem the right way: the right size, and any duct repair the system needs. The steps up add things the homeowner can feel or will use. A sample to adapt:
- Good: a properly sized replacement of the failing system, a new thermostat, the duct repairs the system needs, the manufacturer's warranty, your [workmanship warranty], cleanup and haul away.
- Better: everything in Good, plus [a two stage or variable speed system] for the uneven rooms they mentioned, [duct sealing] and [a first year maintenance plan].
- Best: everything in Better, plus [zoning for the upstairs], [whole home humidity control or air cleaning] and [a longer labor warranty].
Tie every upgrade to a sentence from the comfort questions. If nobody mentioned humidity, humidity control does not belong in Best.
When a homeowner asks about a heat pump against a furnace and air conditioner, explain the choice in plain words and let the load calculation, their fuel and their climate drive it. Do not put an efficiency or savings number on the page unless it comes from the equipment's documented ratings and their own bills.
Present the options
Start with the option that fits what you heard, and say why:
"You told me the upstairs is always hot and you plan to stay at least ten years, so I'd look at Better first. Here's what's in it. Good also replaces the system at the right size and fixes the ducts; what you give up is the variable speed system and the maintenance plan."
If you show a monthly payment, take every number from the lender's documents and show the term and the total too. If repair is a real option for an older system, price the repair as well. A homeowner who chooses to repair today will remember who told them the truth when it fails. The three option guide has more on building and presenting the three.
Warranty and maintenance are real differences
- Manufacturer warranty: check whether the manufacturer requires registration, and register the equipment for the homeowner after the install.
- Labor warranty: yours. Say how long, what it covers and how to call for service.
- Maintenance plan: how many visits a year, what each visit includes, and whether plan members get scheduled first.
After the yes
Hand the crew a file they do not have to rebuild: the load calculation, the equipment chosen, the duct scope with photos, electrical and gas notes, the thermostat location, access notes, the permit, and the date the homeowner asked for, marked as a request. The sales to production guide has a handoff checklist, and the signed to paid guide follows the job to the final payment.
At the final walkthrough, show the homeowner the thermostat and the filter, leave the paperwork, and ask for an honest review the same way you ask every customer. The reviews guide has the wording.
Plumbing and electrical
The same order works for water heater, repiping and panel jobs: ask what the homeowner notices, inspect and measure before you recommend, build options that differ in ways they can feel, and hand the crew the measurements and photos. Keep each trade's technical calls with the licensed people who do the work.
Where GameForce fits
- Online booking pages
- Good, better, best packages with the monthly payment
- Our own e-signature, in person or by link
On select plans, sold deals turn into jobs: schedule the crew, track every stage, and let the homeowner watch progress in their own portal.
Send the invoice, record the payment and track your reps' commissions from the same place.
Bring the load calculation, the duct photos and the three options into one file, so the crew starts where the visit ended.
FAQ
What is a good HVAC replacement sales process?
Comfort questions, a load calculation, a duct check, three options built from the homeowner's own words, a clear recommendation, and a complete handoff to the crew.
How should an HVAC replacement be sized?
By a load calculation for the home, such as ACCA Manual J, which the ENERGY STAR checklist tells homeowners to ask for. Not by the old system's size or a rule of thumb.
What should good, better and best HVAC options include?
Every option fixes the problem at the right size with the duct repairs it needs. Better and Best add things the homeowner asked about, such as steadier temperatures, zoning, humidity control, maintenance and longer labor coverage.
Should a salesperson promise energy savings?
No. Do not promise a savings figure at the table. If the homeowner asks, point to the equipment's documented ratings and their own bills.
Bring your next replacement
Book a demo and bring one recent replacement quote you would like to split into three options, or start a free trial.



